Overview

The KIT_XMC72_EVK, a 272-pin evaluation board is based on the XMC7000 family of devices. XMC7000 MCU is designed for industrial applications. The evaluation board carries a XMC7000D microcontroller, a M.2 interface connector for interfacing radio modules based on AIROC™ Wi-Fi and Bluetooth® combos, SMIF dual header compatible with Digilent Pmod for interfacing HYPERBUS™ memories (currently not supported), and headers compatible with Arduino for interfacing Arduino shields. In addition, the board features an on-board programmer/debugger (KitProg3), a 512-Mbit QSPI NOR flash, CAN FD transceiver, Gigabit Ethernet PHY transceiver with RJ45 connector interface, a micro-B connector for USB device interface, three user LEDs, one potentiometer, and two push buttons. The board supports operating voltages from 3.3 V to 5.0 V for XMC7000D device.
Note: This BSP does not support Wi-Fi/Bluetooth® connectivity examples. To run Wi-Fi/Bluetooth® connectivity examples on this kit, choose a BSP with the appropriate connectivity M.2 module.

To use code from the BSP, simply include a reference to cybsp.h.

Features

Kit Features:

XMC7200D-E272K8384 8MB Flash 272-pin BGA device
Programming interface (Arm® Standard JTAG, Cortex® Debug + ETM with Arm® ETM Mictor)
Reset control with manual reset switch and voltage supervision
Gigabit Ethernet interface
CAN FD interface
M.2 interface connector to connect radio modules based on AIROC™ Wi-Fi & Bluetooth® combos
512-Mbit external Quad SPI NOR Flash that provides a fast, expandable memory for data and code
KitProg3 on-board SWD programmer/debugger, USB-UART and USB-I2C bridge functionality
A micro-B connector for USB device interface
Selectable input supply voltages of 3.3 V and 5.0 V for the XMC7000D device
Three user LEDs, two user buttons, and a reset button for the XMC7000D device
A potentiometer which can be used to simulate analog sensor output
A mode button and a mode LED for KitProg3

Kit Contents:

XMC7200 evaluation board
USB Type-A to Micro-B cable
12V/3A DC power adapter with additional blades
Six jumper wires
Quick start guide

BSP Configuration

The BSP has a few hooks that allow its behavior to be configured. Some of these items are enabled by default while others must be explicitly enabled. Items enabled by default are specified in the KIT_XMC72_EVK.mk file. The items that are enabled can be changed by creating a custom BSP or by editing the application makefile.

Components:

Device specific category reference (e.g.: CAT1) - This component, enabled by default, pulls in any device specific code for this board.

Defines:

CYBSP_WIFI_CAPABLE - This define, disabled by default, causes the BSP to initialize the interface to an onboard wireless chip if it has one.
CY_USING_HAL - This define, enabled by default, specifies that the HAL is intended to be used by the application. This will cause the BSP to include the applicable header file and to initialize the system level drivers.
CYBSP_CUSTOM_SYSCLK_PM_CALLBACK - This define, disabled by default, causes the BSP to skip registering its default SysClk Power Management callback, if any, and instead to invoke the application-defined function cybsp_register_custom_sysclk_pm_callback to register an application-specific callback.

Clock Configuration

Clock	Source	Output Frequency
FLL	ECO	100.0 MHz
PLL	ECO	100.0 MHz
CLK_HF0	CLK_PATH3	200 MHz
CLK_HF1	CLK_PATH1	350 MHz
CLK_HF2	CLK_PATH4	100 MHz
CLK_HF3	CLK_PATH3	100 MHz
CLK_HF4	CLK_PATH2	125 MHz
CLK_HF5	CLK_PATH2	125 MHz
CLK_HF6	CLK_PATH3	200 MHz
CLK_HF7	CLK_PATH5	0 MHz

Power Configuration

System Idle Power Mode: Deep Sleep
VDDA Voltage: 3300 mV
VDDD Voltage: 3300 mV

See the BSP Setttings for additional board specific configuration settings.

API Reference Manual

The KIT_XMC72_EVK Board Support Package provides a set of APIs to configure, initialize and use the board resources.

See the BSP API Reference Manual for the complete list of the provided interfaces.